Note that the template at the bottom creates a smart icon. Then its time to edit the ‘sensor’ section of your configuration.yaml file. time remaining in my example below) or a series of strings, for example the “Status”, which you can then use to develop the value_template in configuration.yaml. Second, look at the response data, it might be an integer ticks (e.g. You can try any of the OIDs to see which work on your UPS, most were OK on my Value II 1600E but if the OID is not supported it will just tell you that.įirst the OIDs from CyberPower need the “.0” at the end, you cannot use just the OID you see in a viewer. The OID is listed at the bottom left and the values when you double click are shown on the right hand panel. Double click a ‘leaf’ on the tree and it will query the OID and return a value. It’s not super intuitive but start after loading the MIB go down the tree with ‘private…enterprises…cps…products…ups’ and work your way down the folder tree in the MIB file and you will see lots of OIDs you can use. Note that my HA is running in Docker on a Ubuntu machine elsewhere on my network at 192.168.1.38 but I never need to enter this anywhere to get everything to work. Easier to just run on the same Windows 10 machine. If you are running this on another computer you would have to put in the IP address of the computer attached to the UPS (192.168.1.7 in my case). In my image below you will see it is connected to ‘localhost’ since I am running the iReasoning Browser on the same computer the UPS is plugged into. Start by selecting your ip address or localhost as the address in the top right box. Choose “File…Open…” and go to the folder where you stored the CyberPower MIB file and select it. Install and start the iReasoning Browser. Use an MIB browser, I used iReasoning MIB Browser ( Free MIB Browser / MIB Browser / SNMP Browser.) Unzip the file, mine was called MIB002-0001-10.mib and I stored it in a folder called “MIB” off the Downloads folder. Note where this is saved, mine was of course in the Windows Downloads folder. Secondly you need to download the latest MIB file from CyberPower at Anyone know of a way I could achieve this? Thanks. time series? Thanks.Įdit: I might not need SNMP for my application - I just want to be able to record (and graph) voltage time series (and possibly power.) Doing this on the Windows PC that is attached via USB is fine, but the CyberPower Panel software doesn’t do this. ?Īnd once it is, activate SNMP via the menu - anyone have a monitor already set up to graph voltage/power etc. Not sure if that makes a difference? But yes, would love to get the Business part working - I assume when it’s working, after logging in by browser everything is displayed etc. Mine is the CP1500EPFCLCD, which seems to be the non-US version of the same UPS discussed in the thread. I am aware of opwnwrt and similar, but this would be for a set and forget stock system for non-techy people, so fiddly things like raspberry pi and flashing ROMswon’t be to their liking (warranty and so forth.) Guess I’ll have to forgo the email notification on the router then. It seems really close, but I’m not sure if I’m just missing something on the setup, or if there is really a “Version 4” out there that I have not located. 5:44:39 PM (2015 ms) : Value: No response (check: firewalls, routing, snmp settings of device, IPs, SNMP version, community, passwords etc) (SNMP error # -2003) 5:44:39 PM (2009 ms) : SNMP Datatype: ASN_UNIVERSAL I selected custom OID with yours for input voltage. I set the Agent port to 1161, clicked Allow Access in SNMPv1 Service, set community to public, and entered the host IP of the system.įrom the test program, I entered Local IP: Any, Device IP: localhost, Port 1161, SNMPv1, community public. In the PowerPanel agent running at localhost:3052, SNMP settings are under Security / Authentication. I downloaded Paessler SNMP Tester and run it on the same Windows 2008r2 server as PowerPanel. In any case I have not been able to make it work. I thought maybe you meant it was added between version 3.3 and 3.4. It does have SNMP settings, which I enabled. The latest version of PowerPanel Business | Windows that I can find to download from CyberPower is version 3.4. I’ve been looking for an API to access the status data. Thanks for pointing out the SNMP in PowerPanel.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |